7.31. Sterownik mbdmn

• Zgodność ze specyfikacją: 4 .

• Obsługiwane urządzenia: Wszystkie urządzenia i systemy SCADA (lub inne oprogramowanie) wykorzystujące protokół Modbus.

• Protokół komunikacji: Modbus RTU (połączenie szeregowe RS232/RS485) lub Modbus TCP/IP.

• Ten sterownik zastępuje starsze sterowniki mbrtudmn i mbtcpdmn.

• Konfiguracja: Sterownik jest konfigurowany w pliku params.xml, wszystkie atrybuty z przestrzeni nazw 'modbus', nie opisane jako opcjonalne, są wymagane.

• Przykładowa konfiguracja:

  <device 
       xmlns:modbus="http://www.praterm.com.pl/SZARP/ipk-extra"
       daemon="/opt/szarp/bin/mbdmn" 
       path="/dev/null"
       modbus:daemon-mode=
   		allowed modes are 'tcp-server' and 'tcp-client' and 'serial-client' and 'serial-server'
       modbud:tcp-port="502"
  		TCP port we are listenning on/connecting to (server/client)
       modbus:tcp-allowed="192.9.200.201 192.9.200.202"
  		(optional) list of allowed clients IP addresses for server mode, if empty all
  		addresses are allowed
       modbus:tcp-address="192.9.200.201"
   		server IP address (required in client mode)
       modbus:tcp-keepalive="yes"
   		should we set TCP Keep-Alive options? "yes" or "no"
       modbus:tcp-timeout="32"
  		(optional) connection timeout in seconds, after timeout expires, connection
  		is closed; default empty value means no timeout
       modbus:nodata-timeout="15"
  		(optional) timeout (in seconds) to set data to 'NO_DATA' if data is not available,
  		default is 20 seconds
       modbus:nodata-value="-1"
   		(optional) value to send instead of 'NO_DATA', default is 0
       modbus:FloatOrder="msblsb"
   		(optional) registers order for 4 bytes (2 registers) float order - "msblsb"
  		(default) or "lsbmsb"; values names are a little misleading, it shoud be 
  		msw/lsw (most/less significant word) not msb/lsb (most/less significant byte),
  		but it's left like this for compatibility with Modbus RTU driver configuration
        >
        <unit id="1" modbus:id="49">
  		modbus:id is optional Modbus unit identifier - number from 0 to 255; default is to
  		use IPK id attribute, but parsed as a character value and not a number; in this 
  		example both definitions id="1" and modbud:id="49" give tha same value, because ASCII
  		code of "1" is 49
                <param
  			Read value using ReadHoldingRegisters (0x03) Modbus function              
                        name="..."
                        ...
                        modbus:address="0x03"
   	                      	modbus register number, starting from 0
                        modbus:val_type="integer">
   	                      	register value type, 'integer' (2 bytes, 1 register) or float (4 bytes,
  	                       	2 registers)
                        ...
                </param>
                <param
                        name="..."
                        ...
                        modbus:address="0x04"
                        modbus:val_type="float"
  			modbus:val_op="msblsb"
  			modbus:val_op="LSW">
  				(optional) operator for converting data from float to 2 bytes integer;
  				default is 'NONE' (simple conversion to short int), other values
  				are 'LSW' and 'MSW' - converting to 4 bytes long and getting less/more
  				significant word; in this case there should be 2 parameters with the
  				same register address and different val_op attributes - LSW and MSW.
  				słowa
                        ...
                </param>
                ...
                <send 
                		Sending value using WriteMultipleRegisters (0x10) Modbus function
                        param="..." 
                        type="min"
                        modbus:address="0x1f"
                        modbus:val_type="float">
                        ...
                </send>
                ...
        </unit>
   </device>